Trade Tracks 220 Forfar St. E. Fergus, Ontario N1M 2X7 519 831 5436 tradetracks.swcl@gmail.com
Showcase 2027 · May 28, 2027


← Back to Student Activities

Safety and supervision

Educators are responsible for assessing each activity, selecting age-appropriate tools and materials, providing appropriate instruction and supervision, and complying with all school, school-board, facility and applicable health and safety requirements. Activities must be modified or omitted when appropriate.

Prepare to Enter the Workforce System

Grade 11 Hands-On Trade Tasks

Five safe applied activities connected directly to PATH and Career Centres

Hands-On Progression

Grade 11: Construct • Assemble • Verify to Specification

These are physical approximations of skilled-work behaviours, not simulations that require students to perform regulated or hazardous trade work.

All activities are classroom approximations of skilled work. Use only teacher-approved materials, tools and spaces. Do not perform energized electrical work, vehicle repair, pressurized-system work, hot work, cutting/grinding, work at height, or power-tool operations unless the school already permits the activity and a qualified teacher provides the required supervision, PPE and procedures. Students may stop an activity when unsure or unsafe.
Canada is a dual-measurement workplace. Students should become comfortable reading and communicating both metric and imperial/US customary measurements where a trade commonly uses them. Use 1 inch = 25.4 mm exactly and 1 foot = 12 inches = 304.8 mm. For classroom estimation, 1 metre ≈ 3.28 feet. Teach students to work in the unit system specified on a drawing or work order, convert only when necessary, label every value with units, and avoid false precision after conversion.
Goes with Activity g11-l1 · Lesson 1

Task 1

Construction Layout Project

Lay out a simple wall, room, pipe or service route on cardboard/floor paper using metric dimensions, then verify selected imperial equivalents.

Setup

  • Use only teacher-approved classroom-safe materials.
  • Provide a clear start/stop signal and accessible student roles.
  • Demonstrate the measurement/tool procedure before students begin.
  • Prepare a no-device Career Centre option if needed.

Student Work Cycle

Plan → Measure/Observe → Do → Check/Test → Record → Improve/Recommend

Trade Connection

Carpenter; Electrician; Plumber; Sheet Metal Worker

WHAT / WHY / WHO / HOW

WHAT What physical or thinking action did I perform?
WHY Why did safety, accuracy, sequence, quality or service matter?
WHO Which workers use a similar skill?
HOW How would someone learn and practise this professionally?
Goes with Activity g11-l2 · Lesson 2

Task 2

Assemble to Specification

Assemble a classroom-safe mock frame, pipe route or duct model from pre-approved materials. Measure finished work against tolerance.

Setup

  • Use only teacher-approved classroom-safe materials.
  • Provide a clear start/stop signal and accessible student roles.
  • Demonstrate the measurement/tool procedure before students begin.
  • Prepare a no-device Career Centre option if needed.

Student Work Cycle

Plan → Measure/Observe → Do → Check/Test → Record → Improve/Recommend

Trade Connection

Construction and fabrication Career Centres

WHAT / WHY / WHO / HOW

WHAT What physical or thinking action did I perform?
WHY Why did safety, accuracy, sequence, quality or service matter?
WHO Which workers use a similar skill?
HOW How would someone learn and practise this professionally?
Goes with Activity g11-l3 · Lesson 3

Task 3

Service Route Coordination

On a wall-section drawing, route mock electrical, plumbing and ventilation services without conflicts; justify sequence and clearances conceptually.

Setup

  • Use only teacher-approved classroom-safe materials.
  • Provide a clear start/stop signal and accessible student roles.
  • Demonstrate the measurement/tool procedure before students begin.
  • Prepare a no-device Career Centre option if needed.

Student Work Cycle

Plan → Measure/Observe → Do → Check/Test → Record → Improve/Recommend

Trade Connection

Electrician; Plumber; HVAC; Carpenter

WHAT / WHY / WHO / HOW

WHAT What physical or thinking action did I perform?
WHY Why did safety, accuracy, sequence, quality or service matter?
WHO Which workers use a similar skill?
HOW How would someone learn and practise this professionally?
Goes with Activity g11-l4 · Lesson 4

Task 4

Work Sample Documentation

Photograph or sketch a safe classroom work sample, record dimensions, role, problem solved, quality check and what you would improve.

Setup

  • Use only teacher-approved classroom-safe materials.
  • Provide a clear start/stop signal and accessible student roles.
  • Demonstrate the measurement/tool procedure before students begin.
  • Prepare a no-device Career Centre option if needed.

Student Work Cycle

Plan → Measure/Observe → Do → Check/Test → Record → Improve/Recommend

Trade Connection

Employer pages related to selected careers

WHAT / WHY / WHO / HOW

WHAT What physical or thinking action did I perform?
WHY Why did safety, accuracy, sequence, quality or service matter?
WHO Which workers use a similar skill?
HOW How would someone learn and practise this professionally?
Goes with Activity g11-l5 · Lesson 5

Task 5

Mock Site / Shop Briefing

In teams, conduct a pre-job briefing: scope, hazards, tools, dimensions, roles, quality standard and stop-work conditions.

Setup

  • Use only teacher-approved classroom-safe materials.
  • Provide a clear start/stop signal and accessible student roles.
  • Demonstrate the measurement/tool procedure before students begin.
  • Prepare a no-device Career Centre option if needed.

Student Work Cycle

Plan → Measure/Observe → Do → Check/Test → Record → Improve/Recommend

Trade Connection

Student-selected employer and Career Centre

WHAT / WHY / WHO / HOW

WHAT What physical or thinking action did I perform?
WHY Why did safety, accuracy, sequence, quality or service matter?
WHO Which workers use a similar skill?
HOW How would someone learn and practise this professionally?
Scroll to Top